Stanton, CA 90680 • North Orange County • Incorporated City • Family-Owned Since 1970 • CSLB #265709
Steel / Metal Stud Framing in Stanton, CA
Light-gauge steel and metal stud framing in Stanton — interior partitions, tenant-improvement walls, soffits, and fire-rated assemblies. We frame the wall so the drywall stays flat: Beach Boulevard shops, Katella and Cerritos interiors, Knott and Western suites, and house remodels. A Stanton mailing label and a Garden Grove or Anaheim job are not the same city hall.
Stanton Framing, Fairfield Crew
Ron Hogan Drywall has been family-owned since 1970. We are based in Fairfield, not a Stanton storefront. This page is steel / metal stud framing in Stanton, CA 90680 — Beach Boulevard, Katella Avenue, Cerritos Avenue, Chapman Avenue, Orangewood Avenue, Knott Avenue, Western Avenue, Dale Avenue, and Magnolia Avenue.
Text “Stanton” with the plans or a photo of the room. If the scope is interior metal studs — or frame-and-hang on the same trip — we schedule it.
Metal Stud Work We Do in Stanton
Interior partition walls
Track, studs, and bracing for new rooms, office layouts, and non-load-bearing walls in 90680. This is the skeleton the board hangs on.
Tenant improvement framing
Retail, restaurant, and office build-outs on Beach Boulevard and along Katella. If the drawing says steel studs, that is the bid. Commercial framing →
Shop and corridor interiors
Suite partitions, market stalls, and rated walls near Rodeo 39, Beach Boulevard retail, and the civic block around City Hall on Katella.
Soffits, bulkheads, and chases
Dropped ceilings, kitchen hood wraps, and framed openings so boxes, ducts, and lights have a home before drywall.
Fire-rated and heavier-gauge walls
Listed assemblies, Type X board later, and heavier studs when the plan or the engineer calls for them. The rating is the whole wall — not the stud alone.
Remodel and ADU partitions
New interior steel walls inside an existing Stanton house when the finish needs a straighter plane than bowed lumber. Wood structure stays wood unless the plan says otherwise. Metal vs wood →
Frame and hang together
One crew frames the metal, hangs the board, and can finish it. Split bids leave missing backing and wavy walls. Services →
Which Stud Belongs on a Stanton Job
| Stud | Use it when | Skip it when |
|---|---|---|
| Light-gauge metal (what we frame) | Beach Boulevard TI, Katella shops, Cerritos and Chapman interiors, rated commercial walls, or a remodel that needs a flat plane for Level 4 / Level 5 | You need beams, columns, or building structure that hold the roof up — that is a different contractor |
| 25-ga interior studs | Short, non-load-bearing partitions with a normal finish | Tall walls, high-abuse corridors, or a spec that names 20-ga or heavier |
| 20-ga / heavier track and studs | Taller commercial walls, restaurant TIs, market build-outs, or engineer notes | A simple closet that never needed the extra gauge |
| Wood studs | Most Stanton house walls off Lampson, Orangewood, and the residential streets between Knott and Magnolia with no commercial spec | The plan already says steel, or the finish will show every bow |
| Furring / hat channel on masonry | Concrete or block walls that need a cavity for boxes before drywall | Glue-only board on a finished living space |
Compare studs: Metal vs wood → · Cost: Is steel expensive? → · Why it stays flat: Steel benefits →
Beach Blvd vs Katella vs the Neighbors
Stanton is an incorporated north Orange County city — ZIP 90680 — about three square miles, bounded by Cypress on the west, Anaheim on the north and east, and Garden Grove on the east and south. A southern strip of Stanton cuts West Garden Grove off from the rest of Garden Grove, so the city limits jog. It is not Anaheim and it is not Garden Grove. Portions of neighboring ZIPs can sit against the line, so a Stanton mailing address can still sit in the wrong city. Permits inside city limits run through the City of Stanton Building Division at City Hall, 7800 Katella Avenue. Text the street so we bid the right desk.
Beach Boulevard (State Route 39) is the north-south commercial spine — shops, restaurants, and Rodeo 39. Katella Avenue is the civic and east-west cut through City Hall. Cerritos Avenue, Chapman Avenue, Orangewood Avenue, and Lampson Avenue pick up more corridor and house traffic. Knott Avenue, Western Avenue, Dale Avenue, and Magnolia Avenue run north-south through the neighborhoods. Garden Grove Boulevard and Gilbert Street only clip the edge. The 22 freeway sits just south.
The usual mismatch is treating a Beach Boulevard tenant wall like a bedroom 2×4 — or hanging a Level 5 restaurant finish on house framing that only needed wood hang-only. Interior metal studs do not hold the building up. Occupied houses, open shops, and after-hours offices need a clean layout, backing for cabinets and TVs, and a stud plane the finish can live with. Matching the spec still beats guessing the gauge. Send the plan sheet or a wide shot of the room. That photo decides wood hang-only vs new metal studs faster than a ZIP code.
How a Stanton Metal-Stud Job Runs
1. Photos + place
Text (925) 791-9099 Stanton, the street, and the plans or a photo of the wall.
2. Name the wall
Partition, TI layout, soffit, rated assembly, shop interior, or frame-and-hang. We will say if the existing framing can take the finish.
3. We frame it
Protect the space. Track, studs, backing, hang if scoped. Ready for inspection and board. 12-month warranty on our work.
Stanton, CA
This page is steel and metal stud framing in Stanton — ZIP 90680, an incorporated north Orange County city, from our Fairfield shop. Permits inside city limits run through the City of Stanton, not Anaheim, Garden Grove, Cypress, Westminster, or Buena Park. Need the board hung and finished on the same job? Services → · Framing basics: Framing guide →
Office: 2380 Palmer Circle, Fairfield, CA · CSLB #265709 · Check the number on cslb.ca.gov.
Not on This Page
No fake Stanton address. No structural steel building. No promise that metal studs hold a commercial hall up. We frame interior light-gauge walls and hang drywall on wood or steel. A closet does not need a shaft-wall spec. This page is Stanton — not Anaheim, Garden Grove, Cypress, Westminster, or Buena Park.
Stanton Metal Stud FAQs
Do you do steel / metal stud framing in Stanton?
Yes. Interior light-gauge metal stud framing in Stanton, CA 90680 from our Fairfield shop — partitions, Beach Boulevard TI walls, shop interiors, soffits, heavier-gauge spec walls, and frame-and-hang.
Is Stanton the same as Garden Grove or Anaheim?
No. Stanton is its own incorporated city. Anaheim sits north and east. Garden Grove wraps south and east and is split by a Stanton strip. Cypress is west. Westminster and Buena Park are separate cities. Text the street so we bid the right city hall.
Is this structural steel?
No. We frame interior light-gauge studs, track, headers, and soffits. Beams, columns, and building structure that hold the roof up are a different contractor.
Do Stanton houses use metal studs or wood?
Most house walls here are still wood. Metal wins on Beach Boulevard TIs, shop interiors, rated partitions, and remodels that need a straighter plane for a smooth finish. If the drawing names the stud, that wins.
Can you frame a shop on Beach Boulevard or Katella?
Yes. Occupied retail and restaurant TIs on Beach Boulevard and Katella Avenue are a usual request — new partitions, soffits, and backing, then hang if the scope includes board.
Do you work occupied Stanton buildings?
Yes. Floors are protected and the layout is planned around an occupied house, an open Beach Boulevard shop, or an after-hours office. A full TI is still a construction job — plan rooms.
Do you work Beach, Katella, Cerritos, Knott, and Western?
Yes. Beach Boulevard, Katella Avenue, Cerritos Avenue, Chapman Avenue, Orangewood Avenue, Knott Avenue, Western Avenue, Dale Avenue, and Magnolia Avenue are on the same framing page. Text the street with the photos.
Who issues the permit in Stanton?
The City of Stanton Building Division at 7800 Katella Avenue. Anaheim, Garden Grove, Cypress, and county land are different desks — that is why the street matters.
How much does metal stud framing cost in Stanton?
It follows the gauge, wall height, how cut-up the layout is, fire rating, access, and whether we only frame or also hang and finish. Photos or plans first. Written scope — no hidden fees.
Are you licensed in California?
Yes. CSLB #265709. Look it up before you book us or anyone else.
Need Stanton Walls Framed Straight — Then Hung?
Call the family-owned crew that has been framing interiors and hanging board since 1970.
Call / Text (925) 791-9099