Huntington Park, CA 90255 • Los Angeles County • Family-Owned Since 1970 • CSLB #265709
Steel / Metal Stud Framing in Huntington Park, CA
Light-gauge steel and metal stud framing in Huntington Park — interior partitions, tenant-improvement walls, soffits, and fire-rated assemblies. We frame the wall so the drywall stays flat: Pacific Boulevard shops, Gage and Florence interiors, Slauson offices, and house rooms off Miles, Rugby, and State Street. A Pacific Boulevard TI and a tight-lot remodel are not the same stud job.
Huntington Park Framing, Fairfield Crew
Ron Hogan Drywall has been family-owned since 1970. We are based in Fairfield, not a Huntington Park storefront. This page is steel / metal stud framing in Huntington Park, CA 90255 — Pacific Boulevard, Gage Avenue, Florence Avenue, Slauson Avenue, State Street, Miles Avenue, Rugby Avenue, Randolph Street, Saturn Avenue, and Zoe Avenue.
Text “Huntington Park” with the plans or a photo of the room. If the scope is interior metal studs — or frame-and-hang on the same trip — we schedule it.
Metal Stud Work We Do in Huntington Park
Interior partition walls
Track, studs, and bracing for new rooms, office layouts, and non-load-bearing walls in 90255. This is the skeleton the board hangs on.
Tenant improvement framing
Retail, restaurant, and office build-outs on Pacific Boulevard, Gage, and Florence. If the drawing says steel studs, that is the bid. Commercial framing →
Soffits, bulkheads, and chases
Dropped ceilings, kitchen hood wraps, and framed openings so boxes, ducts, and lights have a home before drywall.
Fire-rated and heavier-gauge walls
Listed assemblies, Type X board later, and heavier studs when the plan or the engineer calls for them. The rating is the whole wall — not the stud alone.
Remodel and ADU partitions
New interior steel walls inside an existing Huntington Park house when the finish needs a straighter plane than bowed lumber. Wood structure stays wood unless the plan says otherwise. Metal vs wood →
Frame and hang together
One crew frames the metal, hangs the board, and can finish it. Split bids leave missing backing and wavy walls. Services →
Which Stud Belongs on a Huntington Park Job
| Stud | Use it when | Skip it when |
|---|---|---|
| Light-gauge metal (what we frame) | Pacific Boulevard TI, Gage and Florence shops, rated commercial walls, or a house remodel that needs a flat plane for Level 4 / Level 5 | You need beams and columns that hold the building up — that is structural steel, a different contractor |
| 25-ga interior studs | Short, non-load-bearing partitions with a normal finish | Tall walls, high-abuse corridors, or a spec that names 20-ga or heavier |
| 20-ga / heavier track and studs | Taller commercial walls, door-heavy restaurant TI, or engineer notes | A simple closet that never needed the extra gauge |
| Wood studs | Most Huntington Park house walls with no commercial spec — rooms on Miles, Rugby, State, Randolph, and the numbered grid | The plan already says steel, or the finish will show every bow |
| Furring / hat channel on masonry | Concrete or block walls that need a cavity for boxes before drywall | Glue-only board on a finished living space |
Compare studs: Metal vs wood → · Cost: Is steel expensive? → · Why it stays flat: Steel benefits →
Pacific Boulevard vs Gage vs the House Grid
Huntington Park is its own city in southeast Los Angeles County — ZIP 90255 — between Vernon, Maywood, South Gate, Bell, and Cudahy. It is not South Gate and it is not Walnut Park. Walnut Park shares the 90255 ZIP and is unincorporated Los Angeles County. Pacific Boulevard is the commercial spine. Gage Avenue, Florence Avenue, and Slauson Avenue take more corridor shops and offices. Miles, Rugby, State Street, Randolph, Saturn, and Zoe take house streets and side-street commercial.
The usual mismatch is treating a Pacific Boulevard tenant wall like a bedroom 2×4 — or promising a factory-flat skim on a tight-lot house wall that was never framed straight. Occupied shops and occupied houses need a clean layout, backing for cabinets and TVs, and a stud plane the finish can live with. Matching the spec still beats guessing the gauge.
Send the plan sheet or a wide shot of the room. That photo decides wood hang-only vs new metal studs faster than a ZIP code.
How a Huntington Park Metal-Stud Job Runs
1. Photos + place
Text (925) 791-9099 Huntington Park, the street, and the plans or a photo of the wall.
2. Name the wall
Partition, TI layout, soffit, rated assembly, or frame-and-hang. We will say if the existing framing can take the finish.
3. We frame it
Protect the space. Track, studs, backing, hang if scoped. Ready for inspection and board. 12-month warranty on our work.
Huntington Park, CA
This page is steel and metal stud framing in Huntington Park — ZIP 90255, Los Angeles County, from our Fairfield shop. Permits run through the City of Huntington Park. Need the board hung and finished on the same job? Services → · Framing basics: Framing guide →
Office: 2380 Palmer Circle, Fairfield, CA · CSLB #265709 · Check the number on cslb.ca.gov.
Not on This Page
No fake Huntington Park address. No structural steel building. No promise that metal studs hold the house up. We frame interior light-gauge walls and hang drywall on wood or steel. A closet does not need a shaft-wall spec. This page is Huntington Park — not South Gate, not Vernon, and not Walnut Park.
Huntington Park Metal Stud FAQs
Do you do steel / metal stud framing in Huntington Park?
Yes. Interior light-gauge metal stud framing in Huntington Park, CA 90255 from our Fairfield shop — partitions, TI walls, soffits, heavier-gauge spec walls, and frame-and-hang.
Is this Walnut Park?
No. This page is the City of Huntington Park. Walnut Park shares ZIP 90255 and is unincorporated Los Angeles County. South Gate and Vernon are different cities. Text the street so we bid the right parcel.
Is this structural steel?
No. We frame interior light-gauge studs, track, headers, and soffits. Beams and columns that hold the building up are a different contractor.
Do Huntington Park houses use metal studs or wood?
Most house walls here are still wood. Metal wins on commercial TI, rated partitions, and remodels that need a straighter plane for a smooth finish. If the drawing names the stud, that wins.
Can you frame a shop on Pacific Boulevard?
Yes. Occupied retail and restaurant TIs on Pacific Boulevard, Gage Avenue, and Florence Avenue are a usual request — new partitions, soffits, and backing, then hang if the scope includes board.
Do you work occupied Huntington Park buildings?
Yes. Floors are protected and the layout is planned around an open shop or an occupied house. A full TI is still a construction job — plan rooms.
Do you work Pacific Boulevard, Gage, and Florence?
Yes. Pacific Boulevard, Gage Avenue, Florence Avenue, Slauson Avenue, State Street, Miles Avenue, Rugby Avenue, Randolph Street, Saturn Avenue, and Zoe Avenue are on the same framing page. Text the street with the photos.
How much does metal stud framing cost in Huntington Park?
It follows the gauge, wall height, how cut-up the layout is, fire rating, access, and whether we only frame or also hang and finish. Photos or plans first. Written scope — no hidden fees.
Are you licensed in California?
Yes. CSLB #265709. Look it up before you book us or anyone else.
Need Huntington Park Walls Framed Straight — Then Hung?
Call the family-owned crew that has been framing interiors and hanging board since 1970.
Call / Text (925) 791-9099