Holt, CA 95234 • San Joaquin County • Unincorporated • Roberts Island • Family-Owned Since 1970 • CSLB #265709
Steel / Metal Stud Framing in Holt, CA
Light-gauge steel and metal stud framing in Holt — interior partitions, shop walls, soffits, and fire-rated assemblies. We frame the wall so the drywall stays flat: Highway 4 interiors, Whiskey Slough Road shops, and house or farm remodels in 95234.
Holt Framing, Fairfield Crew
Ron Hogan Drywall has been family-owned since 1970. We are based in Fairfield, not a Holt storefront. Holt is an unincorporated San Joaquin County community on Roberts Island, west of Stockton on Highway 4. This page is steel / metal stud framing in Holt, CA — Highway 4, Whiskey Slough Road, and other 95234 addresses. It is not Holt, Michigan.
Text “Holt CA” with the plans or a photo of the room. If the scope is interior metal studs — or frame-and-hang on the same trip — we schedule it. The street decides the bid.
Metal Stud Work We Do in Holt
Interior partition walls
Track, studs, and bracing for new rooms, office layouts, and non-load-bearing walls in 95234. This is the skeleton the board hangs on.
Shop and tenant-improvement framing
Retail, shop, marina, and farm-office build-outs on Highway 4 and along Whiskey Slough Road when the drawing says steel studs. Holt is a small Delta community, not a downtown grid — if the plan names metal, that is the bid. Commercial framing →
Highway 4 and Whiskey Slough interiors
Shop partitions, office walls, and rated assemblies on Highway 4 / State Route 4, South Whiskey Slough Road, and other Holt addresses in 95234.
Soffits, bulkheads, and chases
Dropped ceilings, kitchen hood wraps, and framed openings so boxes, ducts, and lights have a home before drywall.
Fire-rated and heavier-gauge walls
Listed assemblies, Type X board later, and heavier studs when the plan or the engineer calls for them. The rating is the whole wall — not the stud alone.
House, farm, and ADU partitions
New interior steel walls inside an existing Holt house or farm building when the finish needs a straighter plane than bowed lumber. Wood structure stays wood unless the plan says otherwise. Metal vs wood →
Frame and hang together
One crew frames the metal, hangs the board, and can finish it. Split bids leave missing backing and wavy walls. Services →
Which Stud Belongs on a Holt Job
| Stud | Use it when | Skip it when |
|---|---|---|
| Light-gauge metal (what we frame) | Highway 4 shop TI, Whiskey Slough offices, rated walls, or a remodel that needs a flat plane for Level 4 / Level 5 | You need beams, columns, or structure that hold the building up — that is a different contractor |
| 25-ga interior studs | Short, non-load-bearing partitions with a normal finish | Tall walls, high-abuse corridors, or a spec that names 20-ga or heavier |
| 20-ga / heavier track and studs | Taller shop walls, restaurant or office interiors, or engineer notes | A simple closet that never needed the extra gauge |
| Wood studs | Most house and farm walls off Whiskey Slough Road and the Delta roads with no commercial spec | The plan already says steel, or the finish will show every bow |
| Furring / hat channel on masonry | Concrete or masonry walls that need a cavity for boxes before drywall | Glue-only board on a finished living space |
Compare studs: Metal vs wood → · Cost: Is steel expensive? → · Why it stays flat: Steel benefits →
Holt Streets, ZIPs, and Permits
Holt is an unincorporated community in San Joaquin County on Roberts Island, about 7.5 miles west of downtown Stockton. It does not have its own city building desk. The delivery ZIP on this page is 95234. It uses the 209 area code. Permits for Holt addresses run through the San Joaquin County Building Division at 1810 E. Hazelton Avenue, Stockton, CA 95205. City of Stockton permits are a different desk at 501 W. Weber Avenue. Text the street so the bid matches the desk — and so this is Holt, CA, not Holt, Michigan.
Highway 4 / State Route 4 is the east-west corridor through Holt. South Whiskey Slough Road is the local road to the slough and marina. Occupied shops, Highway 4 TIs, farm offices, and house remodels change the layout — not the stud spec.
The usual mismatch is treating a Highway 4 shop wall like a bedroom 2×4 — or hanging a Level 5 commercial finish on house framing that only needed wood hang-only. Interior metal studs do not hold a house up. Occupied houses, open shops, and after-hours offices need a clean layout, backing for cabinets and TVs, and a stud plane the finish can live with. Matching the spec still beats guessing the gauge. Send the plan sheet or a wide shot of the room. That photo decides wood hang-only vs new metal studs faster than a ZIP code.
How a Holt Metal-Stud Job Runs
1. Photos + place
Text (925) 791-9099 Holt CA, the street, and the plans or a photo of the wall.
2. Name the wall
Partition, shop layout, soffit, rated assembly, Highway 4 interior, farm office, or frame-and-hang. We will say if the existing framing can take the finish.
3. We frame it
Protect the space. Track, studs, backing, hang if scoped. Ready for inspection and board. 12-month warranty on our work.
Holt, CA
This page is steel and metal stud framing in Holt — ZIP 95234 — from our Fairfield shop. Permits run through San Joaquin County in Stockton. Need the board hung and finished on the same job? Services → · Framing basics: Framing guide → · Escalon framing: Escalon →
Office: 2380 Palmer Circle, Fairfield, CA · CSLB #265709 · Check the number on cslb.ca.gov.
Not on This Page
No fake Holt address. No claim that we keep a shop on Highway 4. No structural steel building. No promise that metal studs hold a house up. We frame interior light-gauge walls and hang drywall on wood or steel. A closet does not need a shaft-wall spec. Stockton city limits, Tracy, French Camp, and Holt, Michigan are different places. This page is Holt, CA 95234.
Holt Metal Stud FAQs
Do you do steel / metal stud framing in Holt?
Yes. Interior light-gauge metal stud framing in Holt, CA from our Fairfield shop — partitions, Highway 4 and Whiskey Slough Road TIs, house and farm interiors, soffits, heavier-gauge spec walls, and frame-and-hang.
Is this structural steel?
No. We frame interior light-gauge studs, track, headers, and soffits. Beams, columns, and structure that hold the building up are a different contractor.
Do Holt houses use metal studs or wood?
Most house and farm walls here are still wood. Metal wins on Highway 4 shop TIs, rated partitions, and remodels that need a straighter plane for a smooth finish. If the drawing names the stud, that wins.
Can you frame a shop on Highway 4?
Yes. Occupied shop, marina, and farm-office TIs on Highway 4 and along Whiskey Slough Road are a usual request — new partitions, soffits, and backing, then hang if the scope includes board.
Do you work occupied Holt buildings?
Yes. Floors are protected and the layout is planned around an occupied house, an open shop, or an after-hours office. A full TI is still a construction job — plan rooms.
Do you work Highway 4 and Whiskey Slough Road?
Yes. Highway 4 / State Route 4, South Whiskey Slough Road, and other Holt addresses in 95234 are on this framing page. Text the street with the photos.
What ZIPs does this Holt page cover?
95234. Text the street with the photos so the bid matches the Holt, CA address — not Stockton city limits or Holt, Michigan.
Who issues the permit in Holt?
San Joaquin County Building Division at 1810 E. Hazelton Avenue, Stockton, CA 95205. Holt does not have its own city building desk. City of Stockton is a different desk if the address is inside Stockton city limits.
How much does metal stud framing cost in Holt?
It follows the gauge, wall height, how cut-up the layout is, fire rating, access, and whether we only frame or also hang and finish. Photos or plans first. Written scope — no hidden fees.
Are you licensed in California?
Yes. CSLB #265709. Look it up before you book us or anyone else.
Need Holt Walls Framed Straight — Then Hung?
Call the family-owned crew that has been framing interiors and hanging board since 1970.
Call / Text (925) 791-9099