Newark, CA 94560 • South Alameda County • Incorporated 1955 • Family-Owned Since 1970 • CSLB #265709
Steel / Metal Stud Framing in Newark, CA
Light-gauge steel and metal stud framing in Newark — interior partitions, tenant-improvement walls, soffits, and fire-rated assemblies. We frame the wall so the drywall stays flat: Thornton Avenue shops, NewPark Mall suites, Old Town interiors, and house remodels in 94560.
Newark Framing, Fairfield Crew
Ron Hogan Drywall has been family-owned since 1970. We are based in Fairfield, not a Newark storefront. This page is steel / metal stud framing in Newark, CA — Thornton Avenue, Newark Boulevard, Mowry Avenue, Cherry Street, and Jarvis Avenue.
Text “Newark” with the plans or a photo of the room. If the scope is interior metal studs — or frame-and-hang on the same trip — we schedule it. The street decides the bid.
Metal Stud Work We Do in Newark
Interior partition walls
Track, studs, and bracing for new rooms, office layouts, and non-load-bearing walls in 94560. This is the skeleton the board hangs on.
Tenant improvement framing
Retail, restaurant, medical, and office build-outs on Thornton Avenue, at NewPark Mall, and along Newark Boulevard. If the drawing says steel studs, that is the bid. Commercial framing →
Old Town, NewPark, and Civic Center interiors
Shop partitions, restaurant walls, and rated assemblies in Old Town Newark, at NewPark Mall, along Thornton Avenue, and near Civic Center inside city limits.
Soffits, bulkheads, and chases
Dropped ceilings, kitchen hood wraps, and framed openings so boxes, ducts, and lights have a home before drywall.
Fire-rated and heavier-gauge walls
Listed assemblies, Type X board later, and heavier studs when the plan or the engineer calls for them. The rating is the whole wall — not the stud alone.
Ranch remodel and ADU partitions
New interior steel walls inside an existing Newark house when the finish needs a straighter plane than bowed lumber. Wood structure stays wood unless the plan says otherwise. Metal vs wood →
Frame and hang together
One crew frames the metal, hangs the board, and can finish it. Split bids leave missing backing and wavy walls. Services →
Which Stud Belongs on a Newark Job
| Stud | Use it when | Skip it when |
|---|---|---|
| Light-gauge metal (what we frame) | Thornton Avenue TI, NewPark Mall shops, Old Town suites, rated commercial walls, or a remodel that needs a flat plane for Level 4 / Level 5 | You need beams, columns, or structure that hold the building up — that is a different contractor |
| 25-ga interior studs | Short, non-load-bearing partitions with a normal finish | Tall walls, high-abuse corridors, or a spec that names 20-ga or heavier |
| 20-ga / heavier track and studs | Taller commercial walls, restaurant TIs, office interiors, or engineer notes | A simple closet that never needed the extra gauge |
| Wood studs | Most house walls off Lido Faire, Mowry West, NewPark Village, Mayhews Landing, and older ranch streets with no commercial spec | The plan already says steel, or the finish will show every bow |
| Furring / hat channel on masonry | Concrete or block walls that need a cavity for boxes before drywall | Glue-only board on a finished living space |
Compare studs: Metal vs wood → · Cost: Is steel expensive? → · Why it stays flat: Steel benefits →
Newark Streets, ZIP, and Permits
Newark is an incorporated Alameda County city — September 22, 1955. The city ZIP is 94560. It uses the 510 and 341 area codes. Permits inside city limits run through the City of Newark Building Department at 37101 Newark Boulevard, 94560. This page is the City of Newark only. Text the street so the bid matches the address.
Thornton Avenue carries Old Town. Newark Boulevard, Mowry Avenue, Cherry Street, and Jarvis Avenue run the neighborhoods and retail. Occupied shops, NewPark Mall TIs, and Lido Faire and Mowry West houses change the layout — not the stud spec.
The usual mismatch is treating a Thornton Avenue tenant wall like a bedroom 2×4 — or hanging a Level 5 commercial finish on ranch framing that only needed wood hang-only. Interior metal studs do not hold a house up. Occupied houses, open shops, and after-hours offices need a clean layout, backing for cabinets and TVs, and a stud plane the finish can live with. Matching the spec still beats guessing the gauge. Send the plan sheet or a wide shot of the room. That photo decides wood hang-only vs new metal studs faster than a ZIP code.
How a Newark Metal-Stud Job Runs
1. Photos + place
Text (925) 791-9099 Newark, the street, and the plans or a photo of the wall.
2. Name the wall
Partition, TI layout, soffit, rated assembly, NewPark shop, Old Town remodel, or frame-and-hang. We will say if the existing framing can take the finish.
3. We frame it
Protect the space. Track, studs, backing, hang if scoped. Ready for inspection and board. 12-month warranty on our work.
Newark, CA
This page is steel and metal stud framing in Newark — ZIP 94560 — from our Fairfield shop. Permits inside city limits run through the City of Newark at 37101 Newark Boulevard. Need the board hung and finished on the same job? Services → · Framing basics: Framing guide →
Office: 2380 Palmer Circle, Fairfield, CA · CSLB #265709 · Check the number on cslb.ca.gov.
Not on This Page
No fake Newark address. No structural steel building. No promise that metal studs hold a house up. We frame interior light-gauge walls and hang drywall on wood or steel. A closet does not need a shaft-wall spec. This page is the City of Newark.
Newark Metal Stud FAQs
Do you do steel / metal stud framing in Newark?
Yes. Interior light-gauge metal stud framing in Newark, CA from our Fairfield shop — partitions, Thornton Avenue TIs, NewPark Mall interiors, Old Town suites, soffits, heavier-gauge spec walls, and frame-and-hang.
Is this structural steel?
No. We frame interior light-gauge studs, track, headers, and soffits. Beams, columns, and structure that hold the building up are a different contractor.
Do Newark houses use metal studs or wood?
Most house walls here are still wood. Metal wins on Thornton Avenue TIs, NewPark Mall interiors, rated partitions, and remodels that need a straighter plane for a smooth finish. If the drawing names the stud, that wins.
Can you frame a shop on Thornton Avenue or at NewPark Mall?
Yes. Occupied retail and restaurant TIs on Thornton Avenue, at NewPark Mall, along Newark Boulevard, and near Civic Center are a usual request — new partitions, soffits, and backing, then hang if the scope includes board.
Do you work occupied Newark buildings?
Yes. Floors are protected and the layout is planned around an occupied house, an open shop, or an after-hours office. A full TI is still a construction job — plan rooms.
Do you work Old Town, NewPark, and Civic Center?
Yes. Old Town Newark, NewPark Mall, Civic Center, Lido Faire, Mowry West, Mayhews Landing, and other addresses inside city limits are on this framing page. Text the street with the photos.
What ZIP does this Newark page cover?
94560. Text the street with the photos so the bid matches the address inside the city.
Who issues the permit in Newark?
The City of Newark Building Department at 37101 Newark Boulevard, CA 94560.
How much does metal stud framing cost in Newark?
It follows the gauge, wall height, how cut-up the layout is, fire rating, access, and whether we only frame or also hang and finish. Photos or plans first. Written scope — no hidden fees.
Are you licensed in California?
Yes. CSLB #265709. Look it up before you book us or anyone else.
Need Newark Walls Framed Straight — Then Hung?
Call the family-owned crew that has been framing interiors and hanging board since 1970.
Call / Text (925) 791-9099
